Shenzhen Homk Telecom Tech Co., Ltd.

Japan Fujikura 70r fiber fusion splicer

Details

Japan Fujikura 70r fiber fusion splicer


The Fujikura 70R is equipped with a precision, ixed v-groove for splicing single ibers or ribbon iber up to 12 ibers. Incorporating the proven ruggedized features pioneered by Fujikura, the 70R has added automated and enhanced user control features to increase splicing eficiency. A user programmable, automated wind protector expedites the splicing process by automatically closing to initiate the splice process, and opening upon splice completion. A new auto-start “clamshell design” tube heater applies heat to both sides of the splice protection sleeve resulting in a 40-second shrink time for 12-iber ribbon. The result is a total splice process time of approximately 55 seconds! Ruggedness and durability are greatly enhanced by a mirror-less optical system and "severe-impact resistant" monitor. Battery capacity is now 110 splices/shrinks. An innovative transit case doubles as a built-in or mobile workstation and makes splicing easier than ever before.
 1 Automated and programmable wind protector
 2 40-second automated tube heater
 3 Fully ruggedized for shock, dust and moisture
 4 Li-ion battery with 110 splices/shrinks per charge
 5 On-board training and support videos
 6 Internet software upgrades
 7 Multi-function transit case with integrated workstation

Specifications:

Model FSM-70R Fusion Splicer
Applicable Fibers Single-mode (G.652 & G.657), Multimode (G.651), DS (G.653), NZDS (G.655)
Fiber Count Single, 2, 4, 5, 6, 8, 10, 12
Cladding Diameter 125 μm
Coating Diameter Ribbon: 0.25 mm to 0.4 mm, Single: 250 μm and 900 μm
Fiber Cleave Length 10 mm
Typical Average Splice Loss 0.05 dB with SM, 0.02 dB with MM, 0.08 dB with DS, 0.08 dB with NZDS;measured by cut-back method relevant to ITU-T standards
Splicing Time Typical 15 seconds with standard single-mode fiber
Arc Calibration Method Automatic, real-time by using results of previous splice when in AUTO mode; manual arc calibration function available
Splicing Modes 100 preset and user programmable modes
Splice Loss Estimate Based upon dual camera cladding alignment data
Storage of Splice Result Last 2000 splice results stored in the internal memory
Fiber Display X or Y, or both X and Y simultaneously; front or rear monitor display options with automatic image orientation
Magnification 35X to 90X
Viewing Method Dual cameras with 4.7 inch TFT color LCD monitor with anti-reflective coating
Operating Condition 0 to 3,660 m above sea level, 0 to 95% RH, and -10 to 50°C respectively
Mechanical Proof Test 1.96 to 2.25 N
Tube Heater Built-in tube heater with 30 heating modes; auto-start function
Tube Heating Time Typical 40 seconds with FP-5 sleeve, 17 seconds with FP3 (40), 5-15 seconds with Fujikura micro sleeves
Protection Sleeve Length 60mm,40mm,Micro
Splice/Heat Cycles with Battery Typical 110 cycles with power save functions activated
Electrode Life 1,500 ARC Discharges
Power Supply Auto voltage selection from 100 to 240V AC or 10 to 15V DC with ADC-18, 14.8V DC with BTR-09 battery
Terminals USB 2.0 (USB-B type) for PC communication and Mini-DIN (6-pin) for HJS-02/03
Wind Protection Maximum wind velocity of 15m/s (34 mph)
Dimensions 146 W x 159 D x 150 H (mm) / 5.7 W x 6.3 D x 5.9 H (inches)
Weight 2.3 kg (5.1 lbs) with AC adapter; 2.5 kg (5.5 lbs) with battery



Send Inquiry

*

*

*

*

(All * must be filled in)

[ Previous: ]
[ Next: ]